Nottingham Car Keys
Nottingham Car Keys

how to program a ford remote , how to program a ford fob

How to Program a ford remote , How to program a ford key , how to program a ford fob

how to program your ford remote

How to program a ford remote , how to program a ford key , how to program a ford fob

It is not always necessary to be in need of an auto locksmith if your ford remote stops working , this can often be caused by a flat battery in the remote or a flat battery in the car . Often all your ford remote needs is a simple resynch to get it back to normal , and you can save money by doing this yourself on most models as on most ford models its a manual procedure listed in your handbook.

FORD PUMA 1997 – 02 With Infra-Red Remotes
1. Obtain all keys fitted with remote control:
2. Turn ignition switch to position l.
3. Wait approximately 10 seconds.
4. Ensure clock LED illuminates.
NOTE: LED illuminates for approximately 5 seconds.
5. While LED illuminated switch ignition off and
remove key.
6. With LED illuminated: Programming mode activated
for approximately 20 seconds. Proceed as follows:
7. Point key at receiver (located near interior lamp).
8. Press and hold unlock button. After approximately
1 second key LED will flash once.
9. Press lock button 3 times.
10. Release unlock button
11. Continue to point key at receiver until LEDs in clock
and key have flashed 5 times.
12. Make sure LED remains illuminated.
13. Within 20 seconds repeat above procedure to
program remaining keys.
14. To exit programming mode and extinguish clock
LED Switch ignition on and off.
15. Wait approximately 20 seconds and test remote

 
FORD PUMA 1997 – 02 With Radio frequency Remotes
1. Obtain all keys fitted with remote control.
2. Fasten seat belts and close all doors.
3. From position l, turn ignition switch to position II 3
times. Leaving in position I. Programming mode
activated for approximately 20 seconds. LED or fog
lamps ON warning lamp illuminates (some models),
or a beep will be emitted to indicate start of
programming mode.
4. Type 1: Press and hold unlock button.
5. Type 2: Press unlock button.
6. Make sure clock LED or fog lamp on warning lamp
flashes (some models) or wait for beep signal
which indicates correct programming.
7. Wait 2 seconds.
8. Repeat above procedure within 29 seconds to
program remaining keys.
9. To exit programming mode switch ignition on and
wait 20 seconds then test remote

FORD MONDEO 1993 – 96 Remotes
1. Obtain all keys fitted with remote control.
2. Turn ignition switch to position l.
3. Wait approximately 10 seconds.
4. Make sure clock LED illuminates.
NOTE: LED illuminates for approximately 5
seconds.
5. Switch ignition OFF while LED illuminated.
6. Programming mode activated (LED illuminates) for
approximately 20 seconds then:
7. Point key at receiver (located in front door handles).
8. Press and hold unlock button. After approximately 1
second key LED will flash once.
9. Press lock button 3 times.
10. Release unlock button.
11. Continue to point key at receiver until LEDs in clock
and key have flashed 5 times.
12. Repeat above procedure within 20 seconds to
program remaining keys.
13. Switch ignition on and off to exit programming
mode and extinguish clock LED. Wait approximately 20
seconds.

FORD MONDEO 1996-00 With Infra-Red Remotes
1. Obtain all keys fitted with remote control
2. Fasten seat belts and close all doors.
3. Turn ignition switch to position l to position ll at
least 4 times within 6 seconds.
4. Turn ignition switch to position l.
5. Programming mode activated for 10 seconds.
6. Point key at receiver (located in front door handles).
7. Press and hold lock button or unlock button.
8. Wait for beep signal (indicates correct
programming).
9. Repeat above procedure within 10 seconds to
program remaining keys.
10. Start engine for 10 seconds to exit programming
mode.
Note: A maximum of 4 keys can be programmed.

 
All ford models except transit with 3 button remote
1. Obtain all keys fitted with remote control.
2. Turn ignition switch from position 0 to position ll 4
times within 6 seconds.
3. Turn ignition switch to position 0.
4. An beep signal will be emitted by the system,
indicating start of programming mode.
5. Programming mode activated for 10 seconds.
6. Press and hold lock, unlock or boot release button.
7. Wait for beep signal (indicates correct
programming).
8. Repeat above procedure within 10 seconds to
program remaining keys.
9. To exit programming mode turn ignition switch to
position lll or wait 10 seconds.
Note: A maximum of 4 remotes can be programmed.

FORD SCORPIO 1994 – 98 Remotes
1. Obtain all remote controls.
2. Turn ignition switch 4 times to position l. At fourth
turn to position l, DO NOT switch off.
3. Wait for beep signal.
4. Press unlock button.
5. Another beep signal indicates correct programming.
6. Program remaining remote controls within 10
seconds using unlock button.
7. Switch ignition off. Another beep will be heard.
8. From position ll, turn ignition switch as follows,
– Position l
– Position ll
– Position l
– Position 0
– Position l
– Position 0
9. The system should now be in programming mode
Press and hold each remote control lock/unlock
button until system LED flashes rapidly.

 
FORD GALAXY 1995+ Infra-Red & Radio Remotes
1. Obtain all keys fitted with remote control.
2. Close all windows and doors.
3. Insert key into driver’s door lock.
4. Within 5 seconds turn key to unlock position 3
times. Remove key. Programming mode is
activated for 15 seconds (illuminated driver’s door).
5. Early models: Point key at infrared receiver.
Located near rear view mirror.
6. Press and hold lock button within 5 seconds.
7. Press unlock button 3 times
8. Release lock button.
9. Correct programming indicated by:
10. Key LED flashing 5 times.
11. Door LED flashing rapidly 6 times.
12. Repeat above procedure within 15 seconds to
program remaining keys.
13. Wait 15 seconds to exit programming mode.
Note: A maximum of 4 remotes can be programmed.

Ford Transit until 2006 , ford transit connect with 3 button remote

1) insert key in ignition

2) turn ignition from position 0 to position 2 8 times withing 6 seconds ending in the position 2 position

3) the door locks will cycle

4) press any button on each remote to be programed the door locks will cycle each time a remote is pressed

5) switch ignition off

6) check remotes

Copyright © 2017 Nottingham Car Keys